Master tinkerers hatch V1200 boat engine

Master tinkerer Pete Aardema is known for taking the most mundane American engines, like those from a Model A Ford, and making ridiculous horsepower from them, certainly sufficient power to earn world records in land-speed racing.

Master tinkerers hatch V1200 boat engine
Engine
Pete Aardema
Engine
Kevin Braun
Wooden head mockup
con rod, piston, sleeve
Wooden head mockup
in-house rocker arm

Aardema and machinist Kevin Braun, operating from a small workshop on a hill in rural San Diego county in Southern California, are always looking for new projects and they decided this year, at the last minute of course, to display their prototype V1200 to the Performance Racing Industry show in Indianapolis.

They put the massive engine in the back of their truck and trekked halfway cross-country, installing the engine in a small booth in an innocuous hallway of Indianapolis’ convention center. They were a bit out of the way, but by being in that hallway, they likely got more attention for having their prototype nearly into the walkway - it barely fit their space - than if they’d been shoveled into just another row of displays in one of the large halls that comprise the PRI show.

Aardema and Braun, known for mating typical overhead valve engines to bespoke overhead cam-style power plants, started working on their latest project in October of 2014. They decided, since they were unable to race their latest Bonneville entry in the cancelled 2014 Speed Weeks that fell to an overabundance of rain, that they’d look at boat racing for their next challenge. They came up with the V1200 prototype, made to replace the Allison engines and turbines normally used in unlimited hydroplane boat racing.

“Those (Allison) engines are all used up and the people that have them won’t let them go. They’re hoarding them,” Aardema explained. Once the Allison engines disappeared from the hydroplane marketplace, turbines took over but those, he said, “are super expensive because they’re also being used in the oil fields as generators. For that reason the turbines are expensive,” and difficult to acquire.

“Kevin and I thought, ‘let’s build this engine,’ so we fabricated this block and we made four individual cylinder heads with three valves per cylinder, similar to a lot of other engines we’ve built before.”

What they came up with

What they came up with is a 1,200-cubic-inch V-12 engine with single cam, 3 valves per cylinder, two plugs per cylinder, two Vortex belt-driven superchargers and two intercoolers. The entire operation provides about 15 pounds of boost so they can make 3,000 horsepower from the engine, because that’s about what the turbines are making, Aardema said.

In Unlimited power boat racing, piston-derived engines are given an 800-pound weight advantage over the turbines, so Aardema and Braun felt that, with 3,000 horsepower at the crankshaft, they could have an advantage over the turbines.

The engine has an aluminum block and billet aluminum heads. The block is fabricated at their workshop, Mig-welded, heat-treated and then machined. “It’s about 1/2-inch to one-inch material,” Aardema said. The girdle and main caps on the bottom of this massive engine are billet, “Just like the rest of the engines we build.” The V1200 has a 60-degree angle with two intake valves and a single exhaust valve on each of four cylinder heads. The top is blank to whittle out all the water, then we put a one-inch plate on top of it to house the valve train and the camshaft.

“This engine is closer to an Allison than any of the engines that have been made” for this type of racing, due to its size and displacement. “We’re looking for 2.5 horsepower per cubic inch to get our 3,000 horsepower,” Aardema said. There will be electronic fuel injection delivering alcohol (methanol) to the engine.

“This is a non-running prototype,” he said of the unit at the show. “It was a year-old last month and we’ve been working on it a year. We’ve done almost everything in-house except for the line boring. The crank is from Scat, pistons form Arias, and R&R steel connecting rods.” He’s got his Darton sleeves ready for insertion and in-house rocker arms, with a little help from Jesel. “We made the cams ourselves and Elgin is doing our cam grinding,” Aardema said.

Since they have almost everything they need to assemble this beast - the PRI display prototype was a less-weighty empty shell - Aardema and Brown intended to start assembly once they returned to Souther California. “Hopefully it’ll run by May or June; the intent is to get it operational by the second quarter and then off to the dyno. If all goes well, we’ll find a boat to put it in.”

And then they’ll go racing. If past successes are any indication, Pete Aardema and Kevin Braun may be unleashing the next monster engine that dominates boat racing. As it was, they were fortunate not to have their space at PRI invaded by Unlimited hydroplane racers, as well as those that engage in tractor pulling or Offshore Powerboat racing, all of them looking for the next great mechanical solution. This could be it.

V1200 engine specs

- 1192.8 cubic inches
- length: 59.5 inches
- width: 30 inches
- height: 35 inches
- weight: 1200 pounds (approximately)
- single overhead cam
- three valves/cylinder
- two spark plugs/cylinder
- bore: 5.625 inches
- stroke: 4 inches
- electronic fuel injection
- dry sump oiling
- mechanically supercharged

shares
comments
The 2015 Motorsport.com Awards, Part 2

Previous article

The 2015 Motorsport.com Awards, Part 2

Next article

Top 10 photos of 2015: honorable mentions

Top 10 photos of 2015: honorable mentions
Load comments
The one-time Schumacher rival rebooting his career Down Under Prime

The one-time Schumacher rival rebooting his career Down Under

Joey Mawson made waves in the middle of the last decade, beating future Haas Formula 1 driver Mick Schumacher - among other highly-rated talents - to the 2016 German F4 title. A run in F1's feeder GP3 category only caused his career to stall, but now back in Australia Mawson's S5000 title success has set that to rights

General
May 20, 2021
Why Todt’s FIA successor could be cut from the same cloth Prime

Why Todt’s FIA successor could be cut from the same cloth

Jean Todt has signalled that he will not stand for re-election as FIA president. Mark Gallagher analyses the strong credentials of one potential successor…

General
May 2, 2021
The lesson football’s would-be wreckers could learn from racing Prime

The lesson football’s would-be wreckers could learn from racing

OPINION: The greed-driven push for a European Super League that threatened to tear football apart is collapsing at the seams. Motor racing's equivalent, the football-themed Superleague Formula series of 2008-11, was everything that the proposed ESL never could be.

General
Apr 21, 2021
The real-life racing rogues stranger than fiction Prime

The real-life racing rogues stranger than fiction

The forthcoming Netflix film linking the world of underworld crime and motorsport plays on a theme that isn't exactly new. Over the years, several shady figures have attempted to make it in racing before their dubious dealings caught up with them.

General
Jan 31, 2021
The cherished curios kept by motorsport's professionals at home Prime

The cherished curios kept by motorsport's professionals at home

Keeping trophies and momentos of key triumphs is par for the course for motorsport professionals, but what are the most cherished souvenirs picked up by the drivers and engineers who have seen and done it all?

General
Dec 26, 2020
Why motorsport should consider a mid-week future Prime

Why motorsport should consider a mid-week future

International motorsport has been the preserve of weekends, but the pandemic forced Formula E to get creative with its Berlin season finale as four races were held mid-week. Should FE and other series break with tradition and repeat the experiment?

General
Oct 5, 2020
How pragmatic principles made Ron Tauranac a design legend Prime

How pragmatic principles made Ron Tauranac a design legend

Jack Brabham's 1966 world championship campaign in his eponymous car was also a defining moment in the career of designer Ron Tauranac, who would apply the same ethos to his ultra-successful production racing car business, Ralt.

General
Jul 23, 2020
The ingrained failure motorsport must fix to avoid 'turf wars' Prime

The ingrained failure motorsport must fix to avoid 'turf wars'

OPINION: The FIA has warned that the major motorsport championships must not get engaged in 'turf wars' when it comes to the urgent need to re-organising the 2020 calendars, but there are tedious past problems that must be addressed to satisfy all.

General
May 3, 2020